Stavební inženýrství Jobs

I am looking for a geotechnical and structural engineer who can provide detailed design and calculations for a cantilever retaining wall. The wall will be 2.5 meters in height and located on a site with saturated sand (rsat =20kN/m3). The wall must have a design life of more than 20 years. The ideal candidate should have experience in designing retaining walls and be proficient in geotechnical and structural calculations. Skills required for this project include: - Geotechnical engineering - Structural engineering - Retaining wall design - Calculation proficiency - Familiarity with saturated sand soil type. Geotechnical design calculations and structural calculation for reinforcement required. work to eurocode. consider fos of 1.3 (see attachemnet) you havae to do checks for sliding, st...

I'm a residential contractor and need help with a permit for orange county, FL. They are asking me for an information that my actual engineer can't provide to me. " Previous comment not addressed. Update plot plan to include proposed installation and required swale and details. There are impervious surfaces within 20 feet of the property line. Therefore, the plan must show swales to prevent runoff from impacting adjacent property. Swales can either provide storage or convey runoff to the county right of way. If proposing storage, all volume retention calculations must be shown on the plan. If conveying, plan must provide 1 percent site grading which must be demonstrated with elevations.

The borough requires anything above a 4 ft. retaining wall to have structural drawings before work can begin. I'm looking at ~90 linear feet with two angles to block off the back of my lot, starting at ~14 ft high hill to one side and rising upwards of 23 ft in the far back. I have an autocad file of the survey / elevation to help, which I can share if / when we come to terms.

Hello I have undertaken the hire of professional services to complete Lime Mortar repointing of a 2-bed end terrace, which is nearing the end of the work. However as I have concerns about the work undertaken for peace of mind, before the job is complete and signed off for payment, I just want to ensure I am paying for a fully professional lime mortar installation of repointing. For example, I just want to make sure that what would be reasonably expected for the undertaking of lime mortar repointing and been fully adhered to and the job is at a satisfactory level. I want to ensure the process undertaken for lime Repointing has been adhered to and I do not need to worry about any defects in the lime repointing such as cracks, holes, gaps, crumbling etc will occur to a reasonab...

THEY WILL NEED TO BE BASED IN AUSTRALIA WITH AUSTRALIAN QUALIFICATIONS SO IF YOU HAVE A CONTACT THERE YOU CAN BID. I am in need of an experienced engineer who can design footings for a residential structure. I have soil information and geotechnical reports available for the project. However, I am not sure about the preferred foundation type and would need recommendations. The ideal candidate should have the following skills and experience: - Proficient in structural engineering - Familiarity with residential footing design - Knowledge of various foundation types and their suitability for different soil types - Ability to provide recommendations for foundation type based on soil information and geotechnical reports If you are confident in your ability to provide a safe, efficient, and ...

Modular kitchen designer needed for a modern interior design project. The project scope includes a partial room redesign and consultation and recommendations for the overall design. The ideal candidate will have experience with modern design styles and be able to provide suggestions for a color palette. Looking for someone who is creative, detail-oriented, and able to work within a budget.

Design bridge either box CONCRETE or precast prestressed slab , open girder also steel open girder or pedestrian bridge

I am looking for a freelancer who can create structural plans for a pergola that will be built in an area measuring 120 square feet (10x12). The desired material for the pergola is wood. The area has been identified as Wind Zone 3 and the structural plans should be designed with ASCE 7-16 Wind Zone standards in mind. The ideal freelancer for this project should have experience in structural engineering and be familiar with ASCE 7-16 Wind Zone standards. They should also have expertise in designing and constructing wooden structures.

I need the plans for a pergola 10' x 12' with deck.

need to calculate structural loads, critical stress and failure analysis

I need some small calculation work for "STRUCTURAL LOAD CALCULATIONS ,CRITICAL STRESS CALCULATIONS,FAILURE ANALYSIS " for working model.

We are a small hospital chain and have a inhouse construction and design team, we are looking for a freelance structural engeneer who can work on a fee for service.

I want someone to do Structural load calculations ,Critical stress calculations and Failure analysis for my design

Hardwood Flooring Installation in Living Room I am looking for a skilled professional to install solid wood flooring in my living room, which is approximately 1000 sq ft. The ideal candidate should have experience in hardwood flooring installation and must be able to provide references. Skills/Experience: - Experience in hardwood flooring installation - Ability to work with solid wood flooring materials - Excellent attention to detail - Good communication skills - Ability to work efficiently and complete the project on time Please provide a detailed quote for the project, including the cost of materials and labor. Thank you.

I am looking for a freelancer to design and create shop drawings for a residential building in the construction phase. The ideal candidate should have experience in designing and creating shop drawings for concrete structures. Skills needed: - Experience in designing and creating shop drawings for concrete structures - Knowledge of building codes and regulations for residential buildings Experience required: - Experience in designing and creating shop drawings for residential buildings - Experience in working with concrete materials Materials needed: - Concrete Please provide examples of previous work you have done and your availability for the project.

Structural Load Schedule and Design for Small-scale Project

Looking for a skilled individual to create a Primavera plan for a construction project with 50-100 activities. The project has strict deadlines that must be met. Ideal candidates will have experience in construction project management and proficiency in Primavera software. Attention to detail and strong communication skills are also necessary. The project is only structural works with five basements and 26 floors. The basements will be divided into two parts with one part up to ground floor and the other contains the building with 26 floors. Works start from plain concrete , waterproofing then reinforced concrete work

Two contiguous 1964 houses in Waukegan, IL. Shared driveway, probably interested in a terrace/garage there, definitely gates for privacy. Full reno/up of the front of the houses. Include landscape front and backyards, including decorative exterior lighting and amenities.

I am seeking a structural engineer or architect who can provide a calculation for the foundation of two steel tanks, a total weighing 70 tonnes. The project is for our existing business and will be located outdoors. The ideal candidate will have experience in structural design and knowledge of steel materials. The project will require the following: - Calculation for the foundation of two tanks - Analysis of soil conditions - Design of reinforced concrete foundation - Knowledge of steel materials and their properties - Ability to adhere to safety regulations and standards. - AutoCAD desing and experience

I am doing a home remodel changing a bedroom and bathroom to a living room and kitchen (granny suite) and adding a bedroom and bathroom to the garage. I need blueprints to use to pull my permits as honeowner contractor. Granite Falls, NC (Hickory area).

I am looking for a freelancer who can help me with a quantity estimate for a forth comming project. The project requires someone with past work experience in quantity estimation for Steel works. The project needs to be completed ASAP, so the ideal freelancer would have the availability to start right away. Skills and experience needed: - Past work experience in quantity estimation for businesses - Ability to work under tight deadlines - Strong attention to detail - Good communication skills to discuss project requirements and progress updates - Knowledge of relevant software/tools for quantity estimation If you have the required skills and experience, please include your past work in your application. Thank you!

We are the Ridley Road Community Men's Shed. We need to extend one of our sheds and we need a draughtsman to do the plans for this job

Staying within permitted development (going 3m back) and with a very simple design, I am looking for a structural engineer to survey and provide drawings for my builder to commence the project. Many thanks.

I have a BOQ for a ongoing project in which i need to estimate the steel works quantity with weight analysis for each individual item. The work is very basic , like steel hand rails, decks, CAT ladders etc.

I have a partially completed patio that now needs a permit. The plot map, framing, and elevation drawings are done. Need to complete floor plan, Constuction section, foundation, structural details and plan.

Structural design needed for top slab's shuttering and scaffolding using plywood material and scaffolding material. The top slab is 10 m x 5 m and requires a medium load-bearing capacity. Ideal skills and experience for the job include expertise in structural engineering and experience with wood material for construction.

There is one story edification over a bridge. Pillars are the concrete and the beams are the steel. I need someone who knows CSI Bridge. We will work together in this project

A Civil Engineering firm has prepared 36 lots site plan with lot sizes from 7,600. SF to 8,940. SF meeting city's min. 7,600 SF per lot requirement. Problem is size of lots created include areas of 8' wide private access roadway and front, rear and side setbacks of 20', 10' and 7.5' areas leaving a certain lot with buildable area of only 1,900 SF. Thus, I am looking for a CAD technician who can readjust lot boundaries of about half of 36 lots to reduce lot area of lots greater than 7,610 SF to be reduced to less than 7,605 SF to obtain extra SF to be applied to the lot with only 1,900 SF of buildable area.

My project requires the expertise of a civil engineer who has experience with designing and constructing large and complex structures using steel. This project will demand great attention to detail, with a focus on accuracy and quality workmanship. The engineer should have significant experience in structural design, utilizing steel as the primary material. Additionally, experience in site development and transportation engineering means the optimal person for the job will have a range of skills in order to ensure the project is completed successfully and efficiently. Overall, this is a large and complex project, with specifications that require the precision of an experienced civil engineer.

Event center just under 13,000 square feet. Stair case should be CENTERED I also want a loft upstairs for people to sit and relax and an office upstairs 3D rendering is a must

need civil for foundation plan/boq of simple porch 25x20 feet

structure for the foundation plan of a small porch and its boq the architecture part is finished now and attached and we need the foundation plan

I am looking for a skilled cardboard engineer or card structural designer to design displays/standees that meet our exact requirements. We have a general idea in mind but need assistance and more guidance on dimensions. As we are based in the UK, we are looking for an additional design resource to bolster what we do. This could involve up to five displays/standees initially by the right designer, with the potential for regular work depending on the quality of design.

Hi, I need a experienced quantity surveyor who can take off quantity for rebar. High level of accuracy will be needed. Only bid if you have experience in rebar take off. The duration will be 15-20 days. Details will be provided after discussion.

I am looking for an experienced and knowledgeable freelancer to do a vehicle load analysis on a specific structure using SAP2000. The analysis will consider static loads and is for structural design purposes. I will supply the overall dimensions, material data, vehicle and design code data so that the freelancer can do the appropriate analysis. The final deliverable of this project should be a report explaining the results of the analysis and methods used. Experience with SAP2000 is highly preferred for this project.

I need the help of a Mechanical or Structural engineer who can help me with stress analysis of a Piping system and Generate Detailed reports using CAESAR II quite urgently, if you have the skills, kindly reach out to me

I am not skilled in cad but i do much design work. The previous engineer i was working with has been rather disappointing. It has seem to hit a wall and there were some big mistakes. I need to verify some calculations and detail concepts to put on the drawing so i can obtain stamps and seals. Footer Detail CMU Column Detail Wall Section Detail Truss Detail Wood floor framing detail Uplift connector detail Cantilever detail Foundation Plan Truss Plan Floor Framing Plan Roof Framing plan Elevation Views Specs with data and calculations Foundation specs with calculations and factory of safety Truss calculations The structure is 24x56 and i have some cad and revit models. Just need to conclude it. If you have availability i will send you what I have, you can let me know if you can h...

I am in need of a Structural Designer with Precast Experience in USA projects to design parking garages for my upcoming project. The ideal candidate should have experience in designing precast parking garages. Design Codes and Regulations: I will provide specific design codes and regulations to follow for the project. Project Timeline: The project timeline is more than 4 weeks. Skills and Experience: Ideal skills and experience for this job include: - Experience in designing precast parking garages - Knowledge of specific design codes and regulations - Ability to work on a project with a timeline of more than 4 weeks.