Find Jobs
Hire Freelancers

Driving electromagnets from Arduino Schematic

$10-30 USD

Dokončeno
Zveřejněno přibližně před 5 roky

$10-30 USD

Zaplaceno při doručení
I would like to control the strength of 5 electromagnets using a PWM output from an Arduino. I need you to make an schematic and BOM for me; then I will do the prototype and test it. The magnet will need to be powered using an external power supply (12V power supply) I need you to use Altium Designer to make the schematic. Magnet Specs: Voltage: 12V Link:[login to view URL]
IČ projektu: 18523994

O projektu

6 nabídky
Vzdálený projekt
Aktivní před 5 roky

Chcete si vydělat nějaké peníze?

Výhody podávání nabídek na Freelancer

Stanovte si rozpočet a časový rámec
Získejte za svou práci zaplaceno
Načrtněte svůj návrh
Registrace a podávání nabídek je zdarma
Uděleno:
Avatar uživatele
I am a electrical engineer. I will do the circuit but I have a question. Why do you like to use PWM? Are you going to variable the duty cycle to increase and deacrease the force? do you like to increase and decrease the voltage between 0 to 12 volts? or do you like to control the current? If you like to control the current you are going to design a DC-DC Converter. I can design both of them
$55 USD v 1 dni
5,0 (1 recenze)
1,5
1,5
6 freelanceři nabízejí v průměru $31 USD za tuto práci
Avatar uživatele
Hello. Im designing different electronics devices, mostly based on avr, arm MCUs and boards with them like arduino, stm-discovery etc. (autopromotion^)) Do you want a pcb with some small arduino boards( mini, nano) or with pure atmega328 mcu? I can do this. You need 5 mosfer drivers, some protection cuz of inductive load, drivers can be connected to analog pins, so you can pwm them easily. But you should remember, that electromagnet force cant be linearly controlled like led, for example. You will have some force control, but it will not be linear, it cant be much lower than max etc. Give more info and lets talk. I can design using eagle cad - altium is expensive, I dont have normal version. Your budget $$$ is not serious. I can do this, but not for this money. So Im out if it is final.
$25 USD v 1 dni
4,9 (48 recenze)
5,7
5,7
Avatar uživatele
Hello sir. I am an electrical engineer best in arduino prototyping and pcb designing. I can help you create the schematics in fritzing and altium designer. I am sure that you will be satisfied by my work. Thanks.
$45 USD v 1 dni
4,8 (23 recenze)
4,4
4,4
Avatar uživatele
Hi there.I offer you the services for Arduino/PCB designs, I complete the jobs in Altium. I am new on freelancer site, but I am designer expert with 10+ years of experience in Circuit designs, programming, Arduino software development, PCB Layer. You can check our designs in our portfolio. If you want, I will share more designs I completed so far through interview. So I like to discuss the job with you. Lets talk about your project through interview. Thank you.
$25 USD v 1 dni
4,3 (7 recenze)
4,8
4,8
Avatar uživatele
yes buddy,,,me here to accomplish this task, u will feel brotherhood,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
$25 USD v 1 dni
4,6 (28 recenze)
4,1
4,1
Avatar uživatele
I have experience in working with Arduino of about 4 years. I have also worked with PWM for speed control. I have programmed Arduino using the basic registers which will improve its response speed.
$10 USD v 1 dni
4,6 (3 recenze)
2,0
2,0

O klientovi

Pochází z UNITED STATES
CHAPEL HILL, United States
5,0
33
Ověřená platební metoda
Členem od zář 18, 2005

Ověření klienta

Díky! Poslali jsme vám e-mailem odkaz pro získání kreditu zdarma.
Při odesílání e-mailu se něco pokazilo. Zkuste to prosím znovu.
Registrovaných uživatelů Zveřejněných projektů
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Načítání náhledu
Bylo uděleno povolení ke geolokaci.
Vaše doba přihlášení vypršela a byli jste odhlášeni. Přihlaste se znovu.