Hi,
I am a post graduate power electronics engineer and having very good experience in product design and development. I am excellent in embedded design & programming using pic, dspic controllers and MATLAB codding for Power projects, Boot loaders, Bluetooth & GPS designs, CAN communication, EEprom. UART , RF circuits ,Protocols for networking, wi-Fi routers,OBD diagnosis with CAN bus protocols, Electrical vehicles and AC drives, stepper motor controls. I designed sine wave inverters for standalone and grid tie Inverters. I designed projects like Off line UPS up to 3 KVA, 5kW motor controller for electrical vehicles ,synchronous rectifiers, Solar MPPT chargers, Solar trackers, Battery chargers ,Grid tie inverters design with PLL and feedback control circuit emergency light of 66W and Online UPS control cards, Battery Charging power supplies, LED drivers for PWM controlling and dimming, SMPS, Power supplies. I have experience in schematics and PCB design experience in Altium and ORCAD. I am ready to work for you. Please contact for further discussion.
Hello,
I am an embedded engineer with 6 years of industrial experience in microcontrollers programming and hardware design.
I have been working on different microcontroller and different IDEs.
Relevant Skills and Experience
I have worked on STM32,AVR,PIC, ARDUINO and Raspberry pi
I am using altium or eagle for PCB design.
I have a lab setup all tools required to setup any project
Do let me know if you have any questions
yes buddy, me here to work on this project, U will feel brotherhood,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Hi sir I am very interested in this job and I have experience in high skill pcb design I always support first time right designs we will discuss more over on chat
I have more than 5 years experience in embedded systems and PCB design with eagle and altium design software . so I can do your job within a time limit with your satisfaction.
I would like to know more about the details of your project. I an embedded system engineer with many years of experience but new in freelancer.
please feel free to contact anytime
I am an electrical engineer experienced in design. I have good ability in analysis of data and pcb design with excellent component selection. I work under limited time as per required period.
Relevant Skills and Experience
Pcb designing
Data analysis and interpretation
Electrical engineeringexperience
Hi sir, I have read your requirements and would like to inform you that i have full experienced team with me for your task kindly share your projects scope for better understanding of project. We do not charge anything until give you full working project
I have a lot of experience in the development of embedded systems, circuit design and PCB,
as well as in writing embedded software. Familiar with many types of microcontrollers,
LCD displays, sensors and other peripherals, various interfaces and protocols.
Hi,
The data and clock pins on an i2c bus are open drain which means they require a pull up resistor as these pins are pulled to ground during i2C communication. You have 2 resistors in series with SDA and SCL which are wrong. They should be pulled up by a resistor preferable between 3.3k and 10k. After this they can be used for i2c communication.
You have right resistors on Rx and Tx lines as they should be in series. You can contact me for discussing this project.
Best Regards,
I have 6years working experience in this sector. I completed more than 200 projects in electrical, electronics,automation, robotics and biomedical electronics.
Hello.
It's Ashish Talaviya, PCB designer with 4 years of experience in PCB design. PCB design is my deep interest as well as my hobby. I have delivered many PCB layout for successful products.
Sound in:
- Coding in C/C++
- Schematic capture, PCB layout. Geber, footprint design, manufacturing documents
- Manufacturing PCB, Soldering, testing, prototyping
- CAD design in solidworks & product rendering
- BOM management
IDE :
- Altium Designer
- Circuit maker/Studio
- Autodesk Eagle
- Kicad
- Solidworks
- Arduino/Atmel Studio
Best,
Ashish Talaviya
I had previously work with telematics Solutions based on IOT which is Vehicle Tracking System.
Worked In Technology:
1. GPRS
2. GPS
3. Wifi
4. RTOS
5. FOTA
6. CAN
7. BLE
8. SPI
8. I2C
9. PCB Design
9. 32 bit Microcontroller
10. Raspberry Pi
11. Python
12. Arduino
Experience in designing high speed embedded solutions for defense applications and certification. Getting the design right in first revision is my track record.