Power supply design

Hi, I am a post graduate power electronics engineer and having very good industrial experience of 8+ years in R&D and project development. I am excellent welding power supplies design, Plasma ARC power supplies, high frequency transformers design, solar grid tie transformers, electrical vehicles design, circuits design, multi-channel LED Drivers, Regulated power supplies design with universal input to DC output, Audio amplifier, drives design, Filters design for harmonic analysis and Power factor correction, SMPS, LED drivers, DC-DC, AC-DC converters design, PFC interleaved boost converter, Battery management system, Battery chargers, UPS design, sine wave Inverters, solar grid tie inverters, Solar battery chargers and street light systems design from few watts to KW range using Buck, Boost, and Buck –boost, Interleaved boost/buck, Fly back Push Pull and H-bridge inverters. I have very good experience to design high voltage power supplies up to 50KV for capacitor charging power supplies using soft switching topologies. I have work experience to design from few watts to KW range meeting all compliances like EMI/EMC and safety standards UL etc.

Hello Sir, I have 4 years experience in PCB designing in EAGLE( single multilayer and flex). following are some examples of my work 1. ESP12E wifi + relay board + humidity&temp sensor Smart module 2. ESP12S wifi + relay board home automation board. 3. ESP12E wifi + RC522 RFID + BUCk converter module. 4. atmega328au + hm11(BLE)+ relays car actuator module. 5. atmega328au + nrf24l01 + relays smart switch module. 6. atmega328au + mpr121 capacitive touch smart remote. 7. amega328au + LCD display + hc06(later hm10) + amplifier + strain gauge water mapping module. 8. atmega328au + hm10(BLE) + gyroscope + reed sensor + battery charger smart skateboard module 9. Arduino Uno clone. I will provide you all necessary files ( gerber, smd-coordinate, BOM, Eagle(.brd& .sch) ). please, see my portfolio for more sample of my work. or initiate chat for more detail discussion on your project. thanks.

hi hello nice to see your project my self vipin i have 4 years + experience in hardware designing and power electronics (designing of SMPS, DC-DC converters, flyback converters etc) i have read your project, i would like to work on your project, the work done will be perfect. thanks

This is an starting offer for just interact with me. I will handle all work from your side at lowest amount and faster with accuracy. Give me a chance.

Hi, I am an electronics and communication engineer, and I have deep experience in electric and electronic circuit design.

dear employer i like to share my works and efforts with you to get a solution for that project i'd like to get that work thanks

I'm electrical engineer and have master degree o can do your job

please share the required specifications for these project and what is the purpose manse where it going to be use and the pcb specifications etc

I've already designed a smart power supply so hopefully I can work on it as well.

Hi, I would love to work on your power supply design. Being an electrical and electronics engineer, I had experience to work with power supplies and designing them. Message me if you would like to share more details about the project. Thank you

Please share me voltage and current specificaton to me I am interested in this project. I am hardware and PCB design engineer with 3 year experience I already worked few power supply design and mobile charger circuit and also I have knowledge on buck,boost, flyback etc... I will do both schematic and PCB design in Altium depends upon your requirement price will vary so please contact me and give me more specificaton

I can design a power supply by Psim simulator or LT-spice , i am fresh graduation engineer and my graduation project was a power supply (boost converter ) 1Kw with power factor correction.

Designing of electrification work of buildings. Power supply designs. Estimation of work. Estimation of amount.

Hey I can help you in your power supply design from component selection to first prototype. I am exprienced in non-isolated to isolated topologies. I am good in Magnetics. I am post graduate in Power electronics and having a 4 years of exprience in it.

I have a Master of Engineering degree from a Canadian Institute specializing in Power and Power Electronics and have 3+years of Industry experience.

Hi, I work in a company that develop industrial drivers. I can to offer for you a proffissional solution.