Find Jobs
Hire Freelancers

Lighg controlled motor

$30-250 USD

Dokončeno
Zveřejněno před více než 5 roky

$30-250 USD

Zaplaceno při doručení
Note: I am doing this project by my self so I do not need both parts done, I only need the light controlled motor. Please I need the following to be done: Introduction Photoresistor Theory and operation Operational Amplifier: Resistances and voltage divider Operation Complete Circuit diagram Simulation Conclusion Final Project: Light Controlled Motor Due: Dec 18, 2018 at 5:59 PM In the final project, students will design a motor controller based on the light level on a phototransistor. When illumination is very high, the motor will be stopped while 6 volts will be applied to the motor under low light conditions. You will need to measure (characterize) the properties of the phototransistor under both light and dark conditions in order to design the circuit and calculate component values. Be sure to justify all component values and provide calculations for critical parts of your design. A table listing all components and briefly noting how values were derived is required. An op amp is be used in the project along with a TIP-31 transistor. A 20 point penalty will be imposed if the circuit does not function. Good parts layout along with the use of bypass capacitors will greatly increase the likelihood that the circuit meets all specifications. Students working in a group of two will also need to provide an audio signal that is a function of the light level. Here, a 555 timer is to be used as a voltage controlled oscillator (VCO) that will generate a tone at a frequency of 500 Hz (+/-20%) at zero light level and 1500 Hz at full light (0 volts applied to motor). A small speaker or headset can be used to make the output audible and an oscilloscope can be used to verify the frequencies. One possible circuit is provided in the project data sheets folder ([login to view URL]) which can be used as a starting point. Students are free to use other circuits given on the web if they wish. One student is responsible for the design the motor driver hardware and the other student will design the audio signal generator.
IČ projektu: 18369317

O projektu

3 nabídky
Vzdálený projekt
Aktivní před 5 roky

Chcete si vydělat nějaké peníze?

Výhody podávání nabídek na Freelancer

Stanovte si rozpočet a časový rámec
Získejte za svou práci zaplaceno
Načrtněte svůj návrh
Registrace a podávání nabídek je zdarma
Uděleno:
Avatar uživatele
I have gone through your project details "Light controlled motor"Looking for a candidate that is extremely familiar with the responsibilities associated with the role and can perform them confidently? Experience in the full skills
$30 USD v 1 dni
3,9 (3 recenze)
3,8
3,8
3 freelanceři nabízejí v průměru $110 USD za tuto práci
Avatar uživatele
Your work is very urgent I am a professional engineer working for students projects and thesis since past 40 years Offer with $100 milestone, 50 % will be done today Rest by tomorrow Act fast
$250 USD v 2 dnech
4,3 (91 recenze)
6,2
6,2
Avatar uživatele
sir i can do your project its not difficult i am very good in circuit designing i have also design a power amplifer by myself for my home so i can do your work if you give me opportunity i will give you a quality of work.
$50 USD v 3 dnech
5,0 (1 recenze)
1,6
1,6

O klientovi

Pochází z UNITED STATES
United States
0,0
0
Ověřená platební metoda
Členem od pro 17, 2018

Ověření klienta

Díky! Poslali jsme vám e-mailem odkaz pro získání kreditu zdarma.
Při odesílání e-mailu se něco pokazilo. Zkuste to prosím znovu.
Registrovaných uživatelů Zveřejněných projektů
Freelancer ® is a registered Trademark of Freelancer Technology Pty Limited (ACN 142 189 759)
Copyright © 2024 Freelancer Technology Pty Limited (ACN 142 189 759)
Načítání náhledu
Bylo uděleno povolení ke geolokaci.
Vaše doba přihlášení vypršela a byli jste odhlášeni. Přihlaste se znovu.