NASA Contest: Design a “Smart” Fine-Positioning Arm
- Stav: Closed
- Odměna: $4000
- Přijatých návrhů: 11
- Vítěz: TriassicXYZ
Veřejná nástěnka k vyjasnění projektu
-
Pořadatel soutěže - Před 5 let
Please join us in congratulating Triassic R. as the winner for this challenge. Thanks to all of the participants for all of your hard work on this challenge. There were some really great designs and the evaluation was not easy. We hope that many of you will participate in the rest of the challenges that we will be posting over the next few weeks.
- Před 5 let
-
TriassicXYZ
- Před 5 let
Thank you NASA, I feel very honored to be the winner .
- Před 5 let
-
Pořadatel soutěže - Před 5 let
This contest is now closed. Thank you again for all of your hard work on some really great designs. The team will be evaluating the submissions and announcing the winners as soon as we can (likely about 1-2 weeks). There are several other contests currently active with even more launching this month. We look forward to seeing more of this amazing talent! Thanks!
- Před 5 let
-
Sumon205
- Před 5 let
Thanks a lot.....
- Před 5 let
-
Yashaswi26
- Před 5 let
#extended
- Před 5 let
-
Pořadatel soutěže - Před 5 let
This contest has already been extended. The current deadline stands. Best of luck!
- Před 5 let
-
Myrds
- Před 5 let
Hello NASA, I just would like to clarify a requirement based on the submission guidelines, particularly Design Drawings #3. Shall we present the tilt and panning while the Astrobee is attached to the Handrail? May I know what is the coordinate of the location where you want the pan and tilt to be shown? Thank you.
- Před 5 let
-
Pořadatel soutěže - Před 5 let
The pan and tilt functionality can only happen when the Astrobee is attached to the ISS Handrail. Please use the location for Design Drawings #2 or any other location that demonstrates your solution works at the extreme locations of the design.
- Před 5 let
-
Myrds
- Před 5 let
Thank you.
- Před 5 let
-
Myrds
- Před 5 let
Hello NASA, just to clarify, since we are not entitled to create an attaching functionality for this SCA challenge, are we required to use all volume representations in presenting our SCA Designs?
- Před 5 let
-
Pořadatel soutěže - Před 5 let
SFA has no attaching functionality. Assume there is a tool on the end of the SFA which can take any number of those volumes based on your design and sequencing of commands to that tool.
- Před 5 let
-
Myrds
- Před 5 let
Thank you.
- Před 5 let
-
Myrds
- Před 5 let
#extended, kindly extend, thank you.
- Před 5 let
-
Pořadatel soutěže - Před 5 let
We have extended this contest by 1 week.
- Před 5 let
-
Myrds
- Před 5 let
Thank you
- Před 5 let
-
Pořadatel soutěže - Před 5 let
We have extended this contest by 1 week.
- Před 5 let
-
alpha2omega
- Před 5 let
#extended
- Před 5 let
-
Pořadatel soutěže - Před 5 let
We have extended this contest by 1 week.
- Před 5 let
-
Anamishere
- Před 5 let
What is temperature limit? I mean lowest and highest limit.
- Před 5 let
-
Pořadatel soutěže - Před 5 let
Assume that the system will operate in the pressurized ISS environment, and that humans are nearby and could interact or touch elements.
- Před 5 let
-
elite116
- Před 5 let
Hi,I have developed the hand made sheet based design....is it permitted?...other technical details are in PDF
- Před 5 let
-
Pořadatel soutěže - Před 5 let
Yes. Just scan it into your PDF entry.
- Před 5 let
-
elite116
- Před 5 let
Hi there,will it be possible if I submit the PDF file of the design image?
- Před 5 let
-
Pořadatel soutěže - Před 5 let
Yes. Submissions will be done via PDF.
- Před 5 let
Nejlepší návrhy této soutěže
-
Alejandro10inv Colombia
-
createwithwisdom India0
-
Sumon205 Bangladesh0
-
Myrds Philippines0
Jak začít se soutěžemi
-
Zveřejněte svou soutěž Rychlé a snadné
-
Získejte spousty návrhů Z celého světa
-
Zvolte nejlepší návrh Stáhněte si soubory - Je to snadné!