Cojocariu G. Profile

5,0

(3 recenze)

Nyní sledujete

Chyba při sledování uživatele.

Tento uživatel neumožňuje ostatním uživatelům, aby jej sledovali.

Tohoto uživatele již sledujete.

Váš členský plán povoluje pouze 0 sledovaných. Aktualizujte zde.

Úspěšně odebráno sledování

Při rušení sledování uživatele došlo k chybě.

Úspěšně jste doporučili uživatele

Chyba při doporučování uživatele.

Došlo k chybě. Obnovte stránku a zkuste to znovu.

E-mail byl úspěšně ověřen.

$10 USD / hodinu

horodnic de sus,

romania

$10 USD / hodinu

Aktuálně je zde 1:18 odp.

Připojil se srpna 3, 2016

0 Doporučení

Cojocariu G.

@SirScofield

5,0

(3 recenze)

2,7

100%

$10 USD / hodinu

horodnic de sus,

romania

$10 USD / hodinu

100 %

Úspěšně realizované projekty

100 %

V rámci rozpočtu

100 %

Včas

50 %

Poměr opětovného zaměstnání

PCB Layout Designer

I am a hardware developer and layout design engineer with 6+ years experience working with high-bandwidth interface standards (CSI, GMSL, FPD-Link, OpenLDI), SerDes pair with both LVDS and single ended data transmission standards, LED drivers, power supplies circuits (buck, boost, LDO). I also have some experience in IoT products development with modules as BLE, CAN, GNSS, Ethernet PHY, LTE Cat M1/NB1, WWAN. I finished my Bachelor degree in Applied Electronics (2013-2017) and Masters degree in Computer and Communication Networks (2017-2019), Faculty of Electrical Engineering and Computer Science at "Ștefan cel Mare" University of Suceava, Romania. The below PCB projects are just simple designs done during my Bachelor's for TIE which is a design of electronics modules and assemblies contest for students where I won 1st place.

Zobrazit všechny PCB Layout Designers v Romania

Kontaktujte Cojocariu G. ohledně vaší práce

Přihlaste se a proberte všechny podrobnosti prostřednictvím chatu.

Portfolio

Design of two custom programming boards for ESP12 & ESP32 Wifi modules.

ESP modules

The project goal is to design and generate layout and fabrication files for an ECG wireless system.

The ECG wireless system consist of a Bluetooth device, made with CC2640 that will transmit to a Smartphone information’s received from the ECG circuit (ADS1293). Both modules are powered up from a 3V Li-Ion Battery and two Boost Converters (TPS61221 and TPS61222) that will give 3V3 and 5V respectively for both circuits used in the design.

In this project I only contributed with the layout.

Pcb Design 11

This project is a solar battery charger (from the TIE 2016 contest) and it consists of:
-a single chip boost converter with dynamic Maximum Power Point Tracking (SPV1020)
-an output voltage and current controller (SEA05LTR)
-a comparator circuit to detect a low-battery condition (around TL331KDBVR)
-a smart high side driver with built in overcurrent protection function (AUIR3313S)

Pcb Design 10

My duty here was to design and generate layout and fabrication files for a wireless communication module designer by my supervisor professor (Adrian Petrariu).

The wireless communication module consists of a Bluetooth device that will transmit to a Smartphone the identification ID received from an NFC device. Both modules are powered up from a 3.7V battery pack that will recharge once a week via USB. The entire module is made to be portable, being used especially for golf.

The golf club has attached an RFID tag that will be read via the NFC module. The information’s will be sent to a Smartphone via Bluetooth from where the user can see on a map the exact hit position performed. With all of this recorded positions, on the Smartphone will be generated a map that will provide information’s regarding the game play of the golf player.

Pcb Design 09

This is a 5W wireless charger and it consists of:
-a single chip wireless power transmitter
-a full bridge inverter
-an EEPROM
-an energy transfer coil
-ESD protection circuit

Pcb Design 08

This project goal is to design and generate layout and fabrication files for a digital satellite tuner (DVB-S2). It was designed by my mentor teacher at university. I only did the layout. The first image includes the ground planes.

Pcb Design 07

ESP modules

Pcb Design 11

Pcb Design 10

Pcb Design 09

Pcb Design 08

Pcb Design 07

Recenze

Změny byly uloženy

Zobrazeno 1 - 3 z 3 recenzí

Filtrovat recenze podle:

5,0

$146,00 USD

Re-Design two PCB circuits

Great Work. Getting better and better.

Electronics

Electrical Engineering

PCB Layout

Adrien P.

@elcbuy

•

před 7 roky

5,0

$40,00 USD

Design a custom PCB board for manufacturing

Excellent work provided. Very serious designer, willing to help. Happily making the extra-mile in order to provide a perfect work. Will hire again.

PCB Layout

Adrien P.

@elcbuy

•

před 7 roky

5,0

$45,00 USD

Project for SirScofield

Very good start as freelancer for SirScofield. Very nice person to work with. Patient, Willing to learn. Very good design skills in Altium Designer. I will definitely work with him again.

Electronics

PCB Layout

Circuit Design

Adrien P.

@elcbuy

•

před 7 roky

Zkušenosti

Continental Engineering Services

zář 2017 - čvn 2020 (2 roky, 9 měsíců)

I worked in automotive industry projects, both schematic and layout design, with high-bandwidth interface standards (CSI, GMSL, FPD-Link, OpenLDI), SerDes pair with both LVDS and single ended data transmission standards, LED drivers, power supplies circuits (buck, boost, LDO). I also have some experience in IoT products development with modules as BLE, CAN, GNSS, Ethernet PHY, LTE Cat M1/NB1, WWAN.

Vzdělání

Computer and Communication Networks

Universitatea 'Stefan cel Mare' din Suceava,

Romania

2017 - 2019

(2 roky)

Applied Electronics

Universitatea 'Stefan cel Mare' din Suceava,

Romania

2013 - 2017

(4 roky)

Kvalifikace

APTE (Association for Promoting Electronics Technology)

2017

I was awarded with this certificate at the national contest in PCB Design TIE April 2017 (Interconnecting Techniques in Electronics) where I won the 1st prize.