Design 100a buck boost converter.

$30-250 USD

Zavřený

Zveřejněno

skoro před 7 roky

$30-250 USD

Zaplaceno při doručení

Successful candidate will have extensive experience in circuit design. I'm looking for a dc to dc buck boost converter that can handle highly variable input voltage and amperage. The input will range from about 6v- 50v and up to 50amps. The output should be pwm so that it's suited for battery charging and switch between 3 charging stages. All components should be nonproprietary so the item can be retailed. Positive feedback will be given after the design is fully tested. There must be 0 errors in design. Candidate may need to interface with manufacturer.

Circuit Design

IČ projektu: 14127857

O projektu

9 nabídky

Vzdálený projekt

Aktivní před 7 roky

Chcete si vydělat nějaké peníze?

E-mailová adresa

Výhody podávání nabídek na Freelancer

Stanovte si rozpočet a časový rámec

Získejte za svou práci zaplaceno

Načrtněte svůj návrh

Registrace a podávání nabídek je zdarma

9 freelanceři nabízejí v průměru $270 USD za tuto práci

@seshupower

Hi, I am a post graduate power electronics engineer and having very good industrial experience of 8+ years in R&D and project development. I am excellent welding power supplies design, high frequency transformers design, circuits design, multi-channel LED Drivers, Regulated power supplies design with universal input to DC output, Audio amplifier, drives design, Filters design for harmonic analysis and Power factor correction, SMPS, LED drivers, DC-DC, AC-DC converters design, PFC interleaved boost converter, Battery management system, Battery chargers, UPS design, sine wave Inverters, solar grid tie inverters, Solar battery chargers and street light systems design from few watts to KW range using Buck, Boost, and Buck –boost, Interleaved boost/buck, Fly back Push Pull and H-bridge inverters. I have very good experience to design high voltage power supplies up to 50KV for capacitor charging power supplies using soft switching topologies. I have work experience to design from few watts to KW range meeting all compliances like EMI/EMC and safety standards UL etc.

$888 USD v 10 dnech

4,9

(6 recenze)

4,2

@adipdutt

It is possible that you are input is from a wind turbine or even solar panel (rare case). Definitely one can use a Buck Boost converter with a a non filtered PWM for charging Batteries (depending on Cell Chemistry different current temperature more control will be there) I have developed various project throughout the world (power conversion) for renewable energy etc.

$460 USD v 15 dnech

5,0

(3 recenze)

3,1

@sanakashif906

A proposal has not yet been provided

$222 USD v 20 dnech

5,0

(4 recenze)

2,7

@OlektraGroup

dear Sir i can do this project. I can assure you that if you work with me once, you will always work with me for these kind of projects.

$155 USD v 3 dnech

5,0

(1 recenze)

2,1

@SantoshKGD

Hi, Can you please share your complete project requirements, 1) Input 6 to 50V 2) Output voltage range = ? 3) Output Current = 100A max? 4) Size = ? Thanks and Regards, Santosh

$277 USD v 10 dnech

5,0

(1 recenze)

1,2

@Electroduino

I’m a young engineer , working in electrical engineering and electronics industry, Currently, I am working on a project of a solar pumping station, for this project I realized a boost converter (INPUT = 100v and the OUTPUT=400v) and a dc-ac inverter, I can show you the results if you interested. i will be glade to work with if you aword me your project and i promesse you a processionnal work best regards

$100 USD v 7 dnech